Hp Storageworks P2000 Msa Usb Drivers For Mac

Pro

To ensure the integrity of your download, HPE recommends verifying your results with this SHA-256 Checksum value: bb26f5843bdda61dab41cf656c71b88af56a05f90fdc161ec8a332 cp020153.exe Reboot Requirement: Reboot is not required after installation for updates to take effect and hardware stability to be maintained. Installation: To install this component, execute the smart component (CPxxxxxx.EXE) and follow the onscreen prompts.

To uninstall this component, use the Control Panel Add or Remove Programs feature (Programs and Features in some Windows versions). Double-click the HP MSA USB Driver entry and follow the onscreen prompts. NOTE: If you are unable to detect the MSA 2040/P2000 array after installing the USB driver, please power cycle the MSA 2040/P2000 array once. To ensure the integrity of your download, HPE recommends verifying your results with this SHA-256 Checksum value: bb26f5843bdda61dab41cf656c71b88af56a05f90fdc161ec8a332 cp020153.exe Reboot Requirement: Reboot is not required after installation for updates to take effect and hardware stability to be maintained. Installation: To install this component, execute the smart component (CPxxxxxx.EXE) and follow the onscreen prompts. To uninstall this component, use the Control Panel Add or Remove Programs feature (Programs and Features in some Windows versions).

Re: Configuring P2000 G3 using the CLI The USB driver on COM3 port is properly installed with 9600 bit speed per second. But, in addition, HP support said I should connect with Putty.

Hp Storageworks P2000 Msa Usb Drivers For Mac Windows 10

Double-click the HP MSA USB Driver entry and follow the onscreen prompts. NOTE: If you are unable to detect the MSA 2040/P2000 array after installing the USB driver, please power cycle the MSA 2040/P2000 array once. Release Notes.

42 Connecting to the controller CLI port 2. Insert the P2000 G3 Software Support/Documentation CD into the CD drive on a Linux or Windows computer on the network that is connected to your controller enclosure. Use Autorun or manually start the CD. The MSA Device Discovery Tool will run. Follow the instructions to discover the IP addresses of the controller or controllers. Record these IP addresses so that you can specify them whenever you manage the controllers using SMU or the CLI.

Storageworks

Alternatively, you can set network port IP addresses using CLI on HP-UX, Windows, and Linux platforms. Setting network port IP addresses using DHCP 1. Look in the DHCP server’s pool of leased addresses for two IP addresses assigned to “HP StorageWorks MSA Storage.” 2. Use a ping broadcast to try to identify the device through the host’s ARP table.

If you do not have a DHCP server, you will need to ask your system administrator to allocate two IP addresses, and set them using the CLI during initial configuration (described below). Setting network port IP addresses using the CLI port and cable If you did not use the MSA Device Discovery Tool to set network port IP values, set them manually using the CLI port and cable. If you have not done so already, you need to enable your system for using the CLI port. NOTE: For Linux systems, see or Windows systems see Network ports on controller module A and controller module B are configured with the following default values:. Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B). IP Subnet Mask: 255.255.255.0.

Hp Storageworks P2000 Msa Usb Drivers For Mac Mac

Gateway IP Address: 10.0.0.1 If the default IP addresses are not compatible with your network, you must set an IP address for each network port using the CLI embedded in each controller module. The CLI enables you to access the system using the USB (universal serial bus) communication interface and terminal emulation software. The USB cable and CLI port support USB version 2.0. Use the CLI commands described in the steps below to set the IP address for the network port on each controller module. Once new IP addresses are set, you can change them as needed using SMU. Be sure to change the IP address via SMU before changing the network configuration.

Hp Storageworks P2000 Msa Usb Drivers For Mac Pro

Hp storageworks p2000 msa usb drivers for mac download

NOTE: Changing IP settings can cause management hosts to lose access to the storage system. From your network administrator, obtain an IP address, subnet mask, and gateway address for controller A, and another for controller B. Record these IP addresses so that you can specify them whenever you manage the controllers using SMU or the CLI. Use the provided USB cable to connect controller A to a USB port on a host computer. The USB mini 5 male connector plugs into the CLI port as show (generic controller module is shown).

Comments are closed.